Skip to Content
Home └Visual Testing (VT) - Level II └VT Level II Specific Quiz - Set 2

Visual Testing (VT) - Level II

0 %

Completed

Course content

VT Level II Specific Quiz - Set 2

10 XP
Prev Next
Fullscreen Share
Rating
0 0

There are no comments for now.

Join this Course
to be the first to leave a comment.

1. During direct visual examination, ASME Section V, Article 9 permits the use of which aids?
Mirrors to improve the angle of vision and magnifying lenses to assist examination Only remote video equipment Only aids approved by the welding inspector No aids of any kind
2. In translucent visual examination per ASME Section V, Article 9, the artificial light source should:
Be ultraviolet only Have sufficient intensity and be uniformly diffused over the area examined Be a focused spotlight aimed at a single point Be placed on the same side as the observer
3. The purpose of the procedure demonstration required by ASME Section V, Article 9 is to:
Certify the inspector to Level II Establish acceptance criteria for discontinuities Qualify the welder who made the weld Prove the procedure is capable of detecting the specified fine line under the stated examination conditions
4. The minimum illumination requirement of ASME Section V, Article 9 applies to:
The inspector's workstation where reports are written The rated output of the lamp at its source The surface or area being examined The general lighting of the building
5. Under SNT-TC-1A, the near-vision acuity requirement may be met:
With natural or corrected vision Only with natural, uncorrected vision By any means approved by the welder Only with corrective lenses
6. Under SNT-TC-1A, the specific requirements for recertification intervals and criteria are established in the:
Client's purchase order AWS D1.1 code Employer's written practice ASME Section V
7. Under SNT-TC-1A, the document that describes how the employer controls and administers personnel training, examination and certification is the:
Inspection procedure Technique sheet Quality control manual of the client Written practice
8. Under SNT-TC-1A, the certification examinations for a VT Level II normally consist of:
Only an oral examination General, specific and practical examinations General and practical examinations only Only a practical examination
9. Under SNT-TC-1A, the specific examination for Level II should address:
The equipment, operating procedures, techniques, specifications and codes used by the employer The basic physics of light and optics only Management and supervision principles The history of nondestructive testing
10. ANSI/ASNT CP-105 provides:
Rules for the design of inspection fixtures Acceptance criteria for weld discontinuities Standard topical outlines for the training of NDT personnel Illumination requirements for visual testing
11. In AWS D1.1, the allowable undercut for a weld depends on factors such as:
Paint system specified Material thickness, type of loading and direction of stress Welder qualification level only Inspector's certification level
12. Under AWS D1.1, acceptance limits for visible piping porosity are generally:
More restrictive for statically loaded connections Identical for all loading conditions Not addressed by visual inspection criteria More restrictive for cyclically loaded connections than for statically loaded connections
13. Under AWS D1.1, a fillet weld exhibiting overlap at the toe is considered:
An unacceptable weld profile A desirable feature that increases strength Acceptable if fully painted Acceptable in all statically loaded structures
14. In AWS D1.1, inspection performed by the Owner's representative, as distinct from the contractor's own inspection, is termed:
Welder qualification testing Production control Verification inspection Fabrication/erection inspection
15. Under AWS D1.1, which welds require visual inspection?
Only complete joint penetration groove welds Only welds in cyclically loaded structures Only welds selected at random by the Engineer All welds
16. ASME B31.3 distinguishes between 'examination' and 'inspection'. Examination refers to quality control functions performed by the:
Design engineer only Manufacturer, fabricator or erector's examiners Owner's Inspector only Jurisdictional authority only
17. An external visual inspection of an in-service pressure vessel under API 510 typically looks for:
Material mill test certificates only Internal tray damage only Weld procedure qualification records Corrosion under insulation, leaks, damaged supports and coating deterioration
18. Under API 570, corrosion under insulation (CUI) on piping is most likely where:
Piping is made of plastic Insulation is intact and sealed Damaged insulation jacketing allows water to enter and accumulate Piping operates well above the boiling point of water at all times
19. When rejectable indications are found, the VT report should record:
Only the name of the welder Location, type and size of each indication and its disposition against the acceptance criteria Only the total number of indications Only the date the component was manufactured
20. If a VT Level II finds that the written procedure conflicts with the referencing code requirements, the appropriate action is to:
Stop and refer the conflict to the responsible Level III or authority for resolution Ignore the code and follow the procedure Modify the procedure personally and continue Follow whichever requirement is easier to meet